|
Search By Brand
Search By Product
Marine Products
Air Scoops for Carburetors
Alternators & Alternator Brackets
Battery Boxes
Bellhousings
Bezels, All
Bezels, Bow Rails, Quick Pin Cleats
Bezels, Cleats
Bezels, Gauge
Bezels, Hoses / Cables
Bezels, Switches
Bilge Blowers
Bilge Pumps & Switches
Bimini Top Brackets
Breathers, Engine
Buoys, Anchor & Marker
Cables (Control) & Accessories
Carburetor Linkage & Related Parts
Cleats
Drains & Drain Plugs
Drink Holders, Spun Aluminum
Drive Showers
Drivelines & Related Parts
Epoxy Marine Repair Products
Exhaust Headers
Exhaust Silencers
Exhaust Transom Cover Plates
Exhaust, Header Valves
Fittings
Flame Arrestors/Air Filters
Foot Throttles
Fuel Fills
Fuel System Products
Fuse & Junction Strips
Gaskets
Gauge Deck Mounts
Gauges, Auto Meter
Grab Handles
Grease - Neo Synthetic
Hatch Actuators & Accessories
Hinges, Hatch
Hose & Hose Clamps
Impellers, Water Pump
Jet Pump Tools
Kill Switches
Lights
Marine Oil Pans
Motor Mounts
Oil Caps, Valve Cover
Oil Coolers & Brackets
Outboard Products
Paddles & Paddle Clips
Prop Nuts & Kits
Prop Puller, Steel
Prop Shafts (V-Drive, Inboard)
Puke Tanks, Oil
Rub Rail, Trim, & Molding
Sea Strainers
Shifter Knobs
Shifters
Silicone, Marine
Ski Tows
Snap Hooks for Ropes
Starters & Related Products
Steering Hubs, Adapters & Bezels
Steering Hubs - What do you need?
Flat 3/9 bolt Hub, Impy, Lecarra
One Piece 9 bolt, Impy, Lecarra
Flat 3/9 bolt Hub, Grant, Formuling
One Piece 9 bolt, Grant, Formuling
5 bolt Hub for Grant
6 bolt Hub - Momo, Spargi, Isotta Volante R-evo
Billet 6 bolt Caps
2" 3 bolt Adapter, Tapered Hole
4" 3 bolt Adapter, Tapered Hole
6" 3 bolt Adapter, Tapered Hole
Steering Bezels, Spun Aluminum
Misc. Steering Hubs, Cap Covers
Steering Systems & Cables
Steering Wheels
Step Pads
Stringer Washers, Billet Aluminum
Strut Bushings - Marine Shaft Bearings
Swim Steps
Switch Knobs, Billet
Switch Panels, Billet
Tach Cables
Thermostat Kits
Thread Sealants
Throw Cushions
Trailer Related Products
Transmissions, Marine
Trim Controls & Switches
Trim Indicators, Mechanical
Trim Tabs
Uncatagorized
V-Drive Products & Parts
Valve Covers
Valves
Vents
Water Divider Outlets
Water Inlet Crossovers
Water Pumps & Impellers, Engine
Water Spot Remover, Wipe Clean
Wrenches, AN & Sea Strainer
On Sale & Closeout Products
Colors & Anodize vs Perma-Coat
Mike's Corner, Race & Event Coverage
| |
|
Ok,
so you have no idea what parts you need to install a particular wheel.
This page will hopefully explain it. There are basically 2 types of hub
assemblies. The first is the stacked assembly as shown below in the first
picture. This method allows the most flexibility in wheel style and allows
choices in the length from the dash.
The
Hub is a 2-piece assembly consisting of a cap and a hub back and mounting
bolts. Typically these hubs fit specific types of wheels and have an internal
6-bolt pattern which mounts to the popular 3-bolt steering wheel pattern.
3 bolts are used, the other 3 are not, this allows for proper indexing
of the wheel more easily.
The
next component is the adapter. This piece accepts the Hub above and typically
fits on the shaft of a given type or brand of steering system. Adapters
are available in several lengths to enable you to adjust the wheel distance
from the dash. Our billet adapters as shown in the photo below have 12
threaded holes for the hub. You will utilize only 3 of the 12 holes. Again
this done for ease of indexing the steering wheel properly. The back side
of the adapter has a keyed tapered hole that slides over the steering
shaft and is secured with the large nut visible in front of the adapter
in the photo.
The
final piece is optional and is applicable to some systems only...the aluminum
dash bezel. It is strictly a dress-up piece that replace some stock plastic
bezels (or helm covers).
All
Images, Text & Design Components of this website are © 2005 Rex
Marine Corporation |
|
The second type of steering wheel mounting is done with what we call the
1-piece hub below. This part is a fixed length and mounts directly on
the steering shaft of the helm. It is essentially the above Hub and Adapter
assembly melded into one part. The 1-piece hubs are not available for
all wheel styles and come in only one length. The white line in the photo
below is used to illustrate the internal cavity in the hub where it attaches
to the helm. These hubs have 3/4 taper shaft holes common to most steering
systems.
|
|
All
Images, Text & Design Components of this website are © 2005 Rex Marine
Corporation
|
|
|
| |